Doc inlet temp during regen
Got a 2018 Mack MRU with an MP7. Truck has had regen issues since we got it new, been to the dealership multiple times but Mack says they can’t duplicate the issues. Active codes as of right now. P103C00 P20EE00 P046C64 P24F700. Truck is in derate requesting a Sulfur regen. During the regen the Nox inlet is at 1026 PPM and outlet is 1773 PPM.Once the DOC is heated up, it can produce high-efficiency oxidization of the post-injected fuel for the DPF regeneration. Based on the DOC light-off temperature achieved, the in-cylinder post fuel injection along with further modulation of the air system parameters can be used to reach a sufficiently high inlet gas temperature for the DPF ... I have a 2017 Mack/CHU. With an engine light on. The codes that come up are P24D1, P24AF, P249F and P24AO. The first I'm pretty sure is for a … read more. Mike Mcmillan. Shop Foreman/Triage Tech. Associates. 7,331 satisfied customers. I have a 2018 CHU Mack MP8 engine showing me its @ 140% soot.
Did you know?
The Aftertreatment System Technician's Guide … NUMBER:08 ATS REF.:Listed in Table :ATSDATE:February 2008 SUBJECT: ADDITIONAL ENGINE WAS ADDEDPUBLICATION: DDC-SVC-MAN-0036 (7SE63)The Aftertreatment System Technician's Guide (DDC-SVC-MAN-0036) wasrevised to include theDD15 REQUIREMENTSA dded row toTable Maintenance …Jan 15, 2017 · During an active regen, engine exhaust temp is slightly higher than normal but not significantly. Maybe 50 to 100 deg. F at best. The high temps are in the exhaust NOX/DPF filter. Everything upstream of that is pretty much normal from my observations. See this video on an entire active regeneration. Soot load was level 5. performed a parked regen. DOC inlet temp was bias. ... Mack MP8 regen issues. IROC Location Offline Posting Freak Reputation: 335. Thanks Given: 279 Thanks Received: 2910 (1046 Posts) Posts: 2,126 Threads: 155 Joined: Jul 2011 1 01-18-2020, 01:06 AM .4. If present, check the condition of the insulation material around the exhaust pipe between the turbocharger and the ATD.. 5. Check the ATD mounting bands for tightness. If needed, tighten the mounting bands on horizon-tally and vertically mounted ATDs to 30 lbf·ft (41 N·m); on step-mounted ATDs, tighten the mount-ing bands to 15 lbf·ft (20 N·m).
Volvo D13 regeneration. we have couple of trucks on our fleet with the same problem. The forced regen would start but runs indefinetly and not continuously. T he exhaust temp rises to about 500, dpf inlet and outlet reaches up to 920 and then engine suddenly changes tone, shuts of the aftertreatment injector, dpf inlet and outlet temps drop for ...Do they have a DPF like the '11 and newer do that will do a regen ... Doc inlet and dpf inlet/outlet temps. An actual code would help, but ...Also, is the DOC and DPF due for cleaning? It sounds like you have access to Insite. When running a regen you need to open up data monitor and watch all the exhaust temps and doser injector state. Once a regen is initiated the DOC inlet and DPF inlet need to reach about 525 -550 degrees.3. If all sensors check out okay, perform a Low temp by disconnecting DEF metering unit connector then navigating to the Service routines>DFP then perform a low temp regen. Then monitor DOC inlet temp & DPF outlet temp sensor readings: If the DOC oullet temp sensor reading follows the DOC inlet temp sensor reading, replace the failed DPF.The AFI wont kick in tell the DOC and DPF inlet temps reach 500+*f and the DOC temp must stabilize. Whats the turbo command %, turbo speed, boost pressure, …
The DPF thermal regeneration began at the experimental time of about 30 s, from which the target regeneration temperature and the DPF-inlet temperature started to increase gradually. As soon as the DPF-inlet temperature reached the target temperature of 575 °C, the throttle position was quickly reset and the engine dropped to idle.After cleaning the doc it was reinstalled on the truck, reset doc/dpf counters. Performed manual stationary regen, the truck kicks up to 1200-1300 to start regen, the turbo speed starts at around 42k and turbo actuator 92%, egr valve position consistently stays at 0%, exhaust gas pressure about 140, intake manifold pressure about 12.5.After it stopped my truck requested another park regen. If you’re needing that many regens, you may need a new filter or perhaps a sensor. You should go see your truck manufacturer. I should add that 200° is normal temp for your dash to show. Mine goes up to about 225° before the fan kicks in and brings it back down to 200°. ….
Reader Q&A - also see RECOMMENDED ARTICLES & FAQs. Doc inlet temp during regen. Possible cause: Not clear doc inlet temp during regen.
ASL: DOC Inlet Temperature ASL: DOC Outlet Temperature ASL: ASL: SCR Outlet Temperature ASL: SCR Inlet NOX Sensor After-treatment Outlet NOX ASL: Nox conversion AAS: Fuel Doser In'ection Status ASL: Exgas mass rate 'd Connections (paused} Device LMCM21J MCM21T MCM21T CPC04T MCM21T MCM21T MCM21T ACM21T ACM21T ACM21T ACM21T ACM21T MCM21T ACM21TDOC not active. Monitor temperature rise across DOC during regen. Little or no temperature rise indicates DOC not active. DOC Inlet Temperature Sensor non-responsive. Monitor DOC inlet temperature. No temperature change after engine startup indicates sensor problem. Intake Throttle Valve not functioning properly. Listen for the ITV to sweep at ...
ASL: DOC Inlet Temperature ASL: DOC Outlet Temperature ASL: ASL: SCR Outlet Temperature ASL: SCR Inlet NOX Sensor After-treatment Outlet NOX ASL: Nox conversion AAS: Fuel Doser In'ection Status ASL: Exgas mass rate 'd Connections (paused} Device LMCM21J MCM21T MCM21T CPC04T MCM21T MCM21T MCM21T ACM21T ACM21T ACM21T ACM21T ACM21T MCM21T ACM21Ttemperature from inlet temperature to outlet temp erature. The THC from post injection is assumed to be completely combusted inside the DOC (Chen, P . et al. (2014)).6. Start the engine and perform a Parked Regen. 7. Let the regen run for 22 minutes then monitor the DOC inlet pressure. Is the DOC inlet pressure reading at or above 8 kPa (1.16 psi)? a. Yes; the DOC is face plugged. Use the DOC air cleaning tool PN: DSN0ATZ16002. Refer to section "Diesel Oxidation Catalyst Air Cleaning". Verify repair. b. No ...
got real crossword clue during an engine bench test in this study. Based on the dropped to idle (DTI) test, a test method is developed to determine the safe regeneration temperature of the DPF. The results show that when the inlet temperature of the DOC is more than 240 C, the DOC begins ignition and reaches the... inlet temperature sensor. Source: Cummins Quickserve. 2009 Cummins ISL Air Intake Overview ... DOC w/ DPF Emissions Control Systems Service. Exhaust, Intake and ... scratch's shop geometry dashz maths Here's the "normal" values for all of the Aftertreatment Parameters during a Parked Regen. *Note* On a DD13, there are 3 important parameters that will have higher values than the DD15 or DD16. -Turbo Speed 38,000-42,000 rpm. -SCR Inlet NOx Sensor 400-500 ppm. -Actual DEF Dosing Quantity 900-1100 g/h.After it stopped my truck requested another park regen. If you’re needing that many regens, you may need a new filter or perhaps a sensor. You should go see your truck manufacturer. I should add that 200° is normal temp for your dash to show. Mine goes up to about 225° before the fan kicks in and brings it back down to 200°. what is rock chalk mean 11. After the low temp ATD regeneration has run for 20 minutes, monitor the DOC outlet temperature sensor reading. Is the DOC outlet temperature sensor reading within 25°C (45°F) of the DOC inlet temperature sensor? a. Yes; replace the HC doser block. Refer to section "Removal of the Hydrocarbon Doser Block ". Verify repair. b. undergrad advisingd.e.s.a.fred vanflet 2015年8月6日 ... EGT2 is post DOC, and EGT1 is pre DOC. Normal driving, EGT3 will ... intake air temp during a regen. I don't think fuel is added into the ...Throttle Valve Actual NOT USED DURING A PARKED REGEN Fuel Comp Pressure 85 ... DOC Inlet Temp 700 – 950 ° F DOC Outlet Temp 1050 – 1150° F DPF Inlet Pressure 0.5 psi – 1.0 psi DPF Outlet Pressure 0.01 psi to 0.9 psi Doser Injection Status gradual increase from 5% to 45% • DOC inlet temp must be at 525° F or higher to west memorial stadium ASL: DOC Inlet Temperature ASL: DOC Outlet Temperature ASL: ASL: SCR Outlet Temperature ASL: SCR Inlet NOX Sensor After-treatment Outlet NOX ASL: Nox conversion AAS: Fuel Doser In'ection Status ASL: Exgas mass rate 'd Connections (paused} Device LMCM21J MCM21T MCM21T CPC04T MCM21T MCM21T MCM21T ACM21T ACM21T ACM21T ACM21T ACM21T MCM21T ACM21T gunabanaoffice depiotreaching out drawing reference Temperature should NOT MBE 4000 or Exhaust Flap on High DOC Outlet temperature be greater than 100°C (212°F) prior to regen. MBE-900 does NOT close, and there is no HEST Lamp after 25 Monitor smoke control status during regen. Smoke control minutes.) Engine in smoke control mode status should be 0. DOC Inlet Temperature Sensor Monitor DOC ...